When a tree you love has a weak fork or a split limb but is otherwise healthy, cabling can buy it many more years. I climb the tree, check the union and the wood around it, and install flexible cables high in the crown so the limbs share the load in wind, snow and ice. Where a split has already opened, I add steel bracing rods. Cabling supports a tree; it doesn't fix rot, so if the inspection shows the wood is too far gone, I'll tell you honestly and we'll talk about removal instead. I check my installations over time, and estimates are free.
What tree cabling & bracing actually is
Tree cabling and bracing are two ways to support a tree that has a structural weakness but is still worth keeping. Cabling uses flexible steel cables, installed high in the crown, to connect two or more limbs so they share the load when wind, snow or ice pushes on them. Bracing uses steel rods, drilled through the wood, to hold a split or a weak union together. I do both from the inside of the tree, climbing it myself to inspect the union and the wood around it. The goal is not to make the tree look tidy. It is to reduce the chance that a heavy limb tears out and takes half the tree with it. I only recommend it when the wood is sound enough to hold the hardware. If the rot is too far advanced, I will tell you.
Why it matters in East Saint John
Saint John gets the kind of weather that finds weak spots in trees. Ice storms load every branch with extra weight. Windstorms push from directions the tree did not grow to resist. Snow sits heavy on evergreens and on broadleaf trees that still have leaves. A tree with a narrow fork, a bark inclusion or an old split is a candidate for failure in any of those events. Cabling spreads the load so a single limb is less likely to break. Bracing holds a split together so it does not open further. What this avoids is the sudden failure that drops a limb on a roof, a fence, a car or a path. It also avoids losing a tree you value. A mature maple or oak that has taken decades to grow is worth supporting if the wood is still sound. I would rather install a cable than remove a healthy tree.
When to do tree cabling & bracing?
The best time to cable a tree is before the damage happens. I look for a few signs: a narrow V-shaped fork where two limbs meet, a crack or seam running down the bark at the union, a limb that has already split but not yet fallen, or a fork that has bark included in the joint (that is a weak connection). You might also notice the tree leaning after a storm, or a limb that sags more than it used to. Late fall or winter, when the tree is dormant and the leaves are down, is a good time for the inspection and the work. But if a split has already opened, do not wait for a season. Call me, and I will come out to assess it. I would rather look at a fresh crack than a fallen limb.
How I work in Saint John
It starts with a phone call. You describe the tree, and I come out for a free estimate. I walk around it, look at the fork or the split from the ground, and then I climb it. From inside the crown I check the union, the wood around it, and whether there is rot or included bark. I will tell you what I see and what I recommend. If cabling or bracing makes sense, we set a date. On the day, I climb with the hardware, install the cables or rods, and check the tension. I clean up everything I brought, and I leave the wood chips if you want them. After the job, I check my installations over time. I do not just install and disappear. If the tree changes, I want to know about it.
The different cases I see
There are a few common cases. The first is the weak fork: two limbs meeting at a narrow angle, often with included bark. I cable them together so they move as a unit. The second is the split limb: a crack has opened, and the limb is still attached. I brace it with steel rods and often add a cable above. The third is the overextended limb: a heavy branch reaching out over a roof or driveway. I cable it back to the main trunk to reduce the load. The fourth is the multi-stem tree: several stems from one base, each pulling away from the others. I cable them to each other. In every case, I check the wood first. If the rot is too far gone, cabling will not fix it, and I will say so.